Are Office Chair Cylinders Universal

Many office chair cylinders are universal, but is this the case? This article will explore office chair cylinders universal and what makes a cylinder universal, and whether or not office chair cylinders meet this definition. We’ll also look at what some of you may want to consider when purchasing a new office chair cylinder. By the end of this article, you’ll have all the information to decide which office chair cylinder is best for you. Keep reading.

Are Office Chair Cylinders Universal

Office chairs are designed to be comfortable and provide support for our backs, but they can start to sag or become uncomfortable over time. This is often due to the cylinders used to adjust the height of the chair wearing down. When this happens, many people wonder if they can replace the cylinder with any old one – after all, aren’t they all the same? Unfortunately, office chair cylinders are not all universal. Therefore, it would help to consider a few things before purchasing a new cylinder for your office chair.

What Is an Office Chair Cylinder?

An office chair cylinder is a metal rod that connects the base of an office chair to the seat and controls the chair’s height. The cylinder also allows the chair to tilt back and forth. In addition, most office chairs have a gas-lift mechanism that uses air pressure to raise and lower the seat. A knob or lever operates the gas lift on the underside of the seat. The office chair cylinder is typically steel or aluminum and is coated with a protective finish to prevent rusting. The cylinder should be replaced if it becomes damaged or worn.

A Detailed Guide on Are Office Chair Cylinders Universal

Many people think that all office chair cylinders are universal, but this is not the case. While there are some standard sizes, the vast majority of office chairs use proprietary cylinders specific to the make and model of the chair. It is essential to purchasing replacement cylinders from the same manufacturer as your chair.

Find That the New Cylinder

Otherwise, you may find that the new cylinder does not fit properly or does not provide the same level of support as the original. In some cases, you may be able to find aftermarket cylinders that will fit your chair, but it is always best to check with the manufacturer first to be sure. With a bit of research, you can be sure to find the right replacement cylinder for your office chair.

How to Tell if You Need a Cylinder Replacement

Your office chair sees a lot of action. Every time you sit down, get up or lean back in your chair, you rely on the cylinder to provide smooth and consistent movement. Over time, though, the cylinder can start to wear out, causing the chair to feel less stable and making it more challenging to adjust the height. If you think your office chair might need a new cylinder, a few telltale signs are to look for.

If the height adjustment on your office chair is becoming increasingly complex, the cylinder is likely starting to fail. The height mechanism on most chairs relies on a gas spring that allows the seat to be raised or lowered with ease. When the gas spring starts to leak, it can become challenging to adjust the chair’s height, and you may even find that the chair slowly sinks on its own.

Another sign that your office chair cylinder may need to be replaced is if the chair starts to feel less stable. If you notice that the chair wobbles or rocks more than it used to, or if it feels like you’re going to tip over when you lean back, these are all signs that the cylinder is no longer providing adequate support. In some cases, you may even be able to see visible damage to the cylinder, such as dents or scratches.

If your office chair isn’t functioning as it should, it’s essential to take action. A failing cylinder can cause many problems, and it can even make your chair unsafe to use. Replacing the cylinder is a relatively simple process, and it can be done relatively cheaply as well. In most cases, you should be able to find a replacement cylinder that fits your chair at your local office supply store. However, if you’re having trouble finding the right size or model, you may need to order a custom cylinder from an online retailer.

How to Replace Office Chair Cylinder

Need to Be Replaced Is the Gas Cylinder

Office chairs are made to last for many years, but eventually, the parts will start to wear out. One of the most common parts that need to be replaced is the gas cylinder. The gas cylinder is what allows the chair to go up and down. Unfortunately, it can leak over time, making the chair go down on its own or become very difficult to adjust. Luckily, replacing the gas cylinder is a relatively straightforward process that anyone can do with a few simple tools.

What You’ll Need:

– Screwdriver

– Wrench

– New gas cylinder

Step 1: Measure a Gas Cylinder

To ensure that your office chair can provide the proper support, choosing the right size gas cylinder is important. Gas cylinders are measured in terms of their height and diameter, and the correct size will depend on the model of chair you have. In general, taller users will need a taller cylinder, while more comprehensive users will need a wider cylinder.

To measure the height of your cylinder, hold it up next to your chair and make a note of the distance from the seat to the top of the cylinder. To measure the diameter, wrap a tape measure around the middle of the cylinder and note the measurement. Once you have these two numbers, you can match them up with the appropriate size gas cylinder for your chair.

Step 2: Purchase the Correct Size Cylinder

Now that you know the measurements of your gas cylinder, you can purchase the correct size replacement from a variety of online and offline retailers. When shopping for a new cylinder, be sure to pay attention to the weight capacity and the height and diameter. You’ll also want to make sure that the new cylinder is compatible with your chair’s base. Most office chair cylinders are universal, but it’s always best to double-check before purchasing.

With the right size gas cylinder in hand, you’re now ready to replace the old one in your office chair.

Step 3: Remove the Old Cylinder

Begin by turning your office chair upside down and removing the base. With the base removed, you should be able to see the gas cylinder. The cylinder is held in place by a metal ring in most cases. Use a screwdriver or wrench to loosen the ring and remove it from the cylinder. With the ring removed, the cylinder should pull out easily. You can try tapping it lightly with a hammer to loosen it if it’s stuck.

Step 4: Install the New Cylinder

Once the old cylinder is out, reverse the process to install the new one. Start by inserting the new cylinder into the chair and then threading on the metal. Next, use a screwdriver or wrench to tighten the ring until it’s snug against the cylinder. Once the ring is in place, you can reattach the base and turn the chair right-side up.

Test the chair to ensure that it adjusts appropriately and doesn’t leak before using it. Your office chair should be good as new with a new gas cylinder!

This information will help in are office chair cylinders universal.

Where to Buy a Replacement Office Chair Cylinder?

If your office chair starts to sag, it might be time to replace the cylinder. But where can you buy a replacement office chair cylinder? Here are a few places to check:

Replacement Cylinders

1. Office Depot or Office Max

These stores usually carry various office chair parts, including replacement cylinders. You may be able to find the exact match for your chair, or you can opt for a universal replacement that will fit most chairs.

2. Amazon

Amazon is an excellent resource for finding anything, and replacement office chair cylinders are no exception. You’ll find a wide selection of options, including both universal and specific replacements.

3. eBay

eBay is another good option for finding replacement office chair cylinders. You’ll find a wide variety of cylinders to choose from, and you may be able to get a good deal on a used or refurbished model.

4. Specialty Office Chair Stores

Some stores specialize in office chairs and their parts. These can be a great option if you’re having trouble finding what you need at the big box stores. Just search for “office chair parts” or “office chair cylinders” to find these stores.

5. Ask Your Chair Manufacturer

If you’re having trouble finding a replacement cylinder, your best bet may be to contact the manufacturer of your office chair. They should be able to tell you where to buy a replacement or sell you one directly.


Are office chair cylinders universal? Unfortunately, all office chair cylinders are not universal. However, there are a few things you should take into account before purchasing new ones for your office chairs. First, make sure that the new cylinders fit the existing holes in your chair’s base. Also, consider the height of your desk and how much space you have underneath it to accommodate the new cylinders. Finally, be aware that different chair bases may require different types of cylinders. So, if you have a rolling or pedestal-style chair base, make sure to get cylinders compatible with those styles.

You may read also How to Make Office Chair Higher

Photo of author

Angela Ervin

Angela is the executive editor of officefixes. She began her career as an interior designer before applying her strategic and creative passion to home and office design. She has close to 15 years of experience in creative writing and online content strategy for Office design and decor,home decorations as well as other efforts. She loves her job and has the privilege of working with an extraordinary team. She lives with her husband, two sons, and daughter in Petersburg. When she's not busy working she spent time with her family.

Leave a Comment